Simple Wedding Rose Fascinator Tutorial

I made this hairpiece/fascinator for my friend’s wedding. She was one of my bridesmaids and really liked the ones I made for my wedding, so with her input on styles and colours she liked, I came up with this:

11147128_10103565300461372_4980807961626696655_o

Photo credit: Trinh Truong and Mai-Anh Doan

She looked stunning on her own, but I like that I had a small part to play in the look of her big day ūüôā

She asked if I would also make one for her mom as a surprise, though without the veil part. Here is a shot with both. Such a sweet idea.

11709968_10103534856705902_8142410299711936026_o

Supplies:

  • 2″ x 25″ piece of fabric (I used tightly-knit jersey material. Finer or more easily fraying fabrics may require you to double up the material, meaning a 4″ x 25″ piece folded lengthwise)
  • scrap piece of same fabric about 3″ x 3″
  • embroidery thread and needle with large enough eye to accommodate
  • tulle for veil
  • broad ribbon (at least 2″ wide and ideally not satin) for leaves
  • artificial stamens (available at most craft stores)
  • hot glue gun
  • clear-drying fabric glue
  • Swarovski or other glue-on crystals (optional)
  • clear-drying tacky glue (if adding crystals)
  • alligator-style clip or other hair clip

Step 1:

Take the strip of fabric and fold it in on itself repeatedly without overlapping the folds (see image below). Then hand sew along the two sides as shown using a basting stitch. Knot off at the far right (as in image) and not at left. Take ends of string and gather fabric. You will see the rose shape form. Now tie off end. Arrange rose shape as you would like and use hot glue to tack in place. Poke stamens through. Now hot glue rose shape in place as desired. Let dry.

katie-hair-thing

Step 2:

To create one leaf (you will need to repeat this step for multiple leaves), cut four pieces of ribbon long enough that two pieces side-by-side form a square-ish shape (exactitude is not crucial). Lay two pieces one positioned above the¬†other side-by-side (like the image on the right below)¬†on top of cellophane or other piece of smooth plastic you don’t mind potentially getting glue on (paper will come away with the glue one dried, ruining your leaf). Apply a uniform, thin layer of fabric glue all over the upwards facing sides of both pieces of ribbon. Place the other two pieces on top, side-by-side (like the image on the left below). Press together and let dry. Basically you will have a ribbon and glue “sandwich” with the “spines” (where the ribbons meet) being perpendicular for stability.

leafs2

One your “sandwich” is dry, you can draw on a leaf shape and cut it out (see image below).

combined leaf

Step 3:

Run fabric glue along raw, cut edge of ribbon leaf to stop fraying. Dab off excess. Let dry.

Step 4:

Position and hot glue leaves and tulle in place on back of rose.

Step 5:

Sew alligator clip to fabric square. Position on back of rose and hot glue on. Trim as needed (rose will obviously not be a perfect square shape).

Step 6:

Use clear tacky glue (apply with a toothpick) to add crystals if desired.

TIP: don’t worry if tulle doesn’t lay exactly right. That’s what steam and hairspray is for ūüėČ

Advertisements

Making Maker Programs

In case you haven’t heard, maker culture is here, it is awesome, and it is an integral part of the future of libraries (don’t believe me? Read this).

Over the past 6 months or so a colleague and I have introduced a maker program for kids at our library called. We¬†choose science, technology, and art activities that are¬†self-directed, allowing the children to use their imagination and inventive skills. We’ve done everything from making musical stairs and game controllers out of MaKey MaKey, to making boats out of recycled material and then having a contest to see which boat can float the most potatoes, to creating stamps for making prints, to making and launching foam rockets.

This past Wednesday we experimented with¬†squishy circuits. Squishy Circuits is a project that came out of the Thomas Lab at St. Thomas University’s School of Engineering (watch the TED Talk here) with the goal of exposing children to electricity, physics, and engineering¬†in a fun and interactive way – with LEDs, toy motors and buzzers, and dough!

A Creeper from Minecraft with a glowing heart (LED covered in conductive dough) created by one of our kids.

I had to adapt the Squishy Circuits program to our library’s environment. Our demographics are such that we get a lot of younger children as opposed to adolescents and teens, many of whom struggle in school for reasons as varied as socio-economics and being newcomers to Canada. Socio-economics is also why many of the kids in our neighbourhood are not familiar with electronics and technology.¬†Hence I needed to keep our Squishy Circuits program simple and be sure I gave them a little bit of preamble on the basics of circuits, and show them a couple of examples of squishy circuits I made in advance. Though many people involved in maker culture will tell you this goes against the investigative spirit of maker culture and its focus on learning through doing and learning from failure, I can tell you that if I didn’t do this the kids wouldn’t have had¬†the slightest idea what to do and therefore had no starting point from which to start experimenting – they would just leave in frustration. It has happened before. Through trial and error I found that once I do this preamble, they get it and are fully willing and able to experiment and explore on their own. They might need a little more coaching and/or reminding here and there of the science or concept behind what we are doing, but by the end they usually all get it.

So, without further adieu, here is my program outline as a pdf:

Squishy Circuits as a public library kids program

It¬†covers the teaching method I used in order to communicate to the kids the concepts necessary to understanding how to make use of the dough and electronics. It also talks about safety concerns and the materials you’ll need. Below I go over how to find and assemble the electronic components if it’s not something you are familiar with (how to know which battery packs to get, what voltage should the LEDs and motors require, how to solder, etc.). Unfortunately the Squishy Circuits website doesn’t cover this. But believe me, the materials are all readily available and no great knowledge of electricity and electronics is required. This whole tutorial is also available on Instructables.

These battery packs, toy motors, and LED lights I bought at an electronics hobby store because I found them there at the best price (budgets are always a concern for libraries!) however if you take apart many toys and gadgets, you’ll find these items inside.

If you find you have bare wire ends like this

     or this    

then you will need to solder terminals on. Terminals can be bought very cheaply at hobby and electronics stores, or online. I used fork shaped ones like this

but really, you could use spade or circle shapes too. It doesn’t matter.¬†I like the ones with an end that is meant to be crimped to the wire with needle nose pliers or a wire crimper (see photo). It just makes the soldering part easier because the terminal will be kept somewhat in place. Heck, if you are really good and the terminal holds on its own after crimping, you might not even need to solder. But, if you have super steady hands, or a second set of hands to help you, then go ahead and try the flat end ones! Just don’t buy terminals with a plastic end. You will have nothing to solder to!

A soldering iron and solder can be bought at an hobby/electronics store, or a hardware store. A cheap soldering iron will do the job just fine, and any solder is good as long as it is not a super thick gauge and it is not acid flux. No clean is ideal, and lead-free is not, but these are not hard-and-fast rules.

I promise that¬†soldering is not that difficult. In fact, it’s a lot of fun. Here is a great tutorial.

A quick note: if you find you have some sort of specific end to a battery pack, like the one below, you can still use it. You will just need a wire stripper/crimper to cut the end off and strip back some of the black and red coating to reveal the wire in order to be able to solder it to a terminal.

In terms of what kind of battery pack to get, it is actually not a huge deal. 4 x AA is ideal, but we were able to get 2 x AAA to work, though the battery wires had to be placed very close to motor or LED light within the dough in order to work. Also, the lower the volt requirement for the LEDs and motors, the easier they will be to make run.

The dough instructions are of course very simple. Just follow the directions on the Squishy Circuits website.

Et voilà!

That’s it, now you can get makin’ :

Slipper sole tutorial

As mentioned in my last post, I’ve been working on making a pair of slippers for my husband in colours from Fallout, his favourite video game. It’s been a huge undertaking, since I couldn’t find any patterns that were the style he wanted that went up to size 13. The closest I could find was this pattern, which I’ve had to heavily modify. On top of all this, he wanted a hard sole. Geeze, the demands of those who don’t craft and have no idea how complicated the thing that they are asking for is.

Well… I’m proud to say I’m finally done! The pattern to follow soon.

In the meantime, I thought I would share how I made the soles. I also put the tutorial up on Instructables, where you can download it as a pdf.

Supplies:

  • patterned/textured PVC fabric (available at most large fabric stores)
  • craft foam
  • fabric on the thicker side (cotton is suggested, I used an old pair of jeans)
  • cardboard
  • pen
  • quality large scissors (you will be cutting through the PVC)
  • Shoe Goo
  • popsicle stick or other instrument for spreading glue that you are prepared to not get back

Step 1:

Make a template by tracing the outline of the person’s foot using the cardboard and pen. Compare it to the bottom of the actual slipper and make any necessary adjustments. Cut out your finished template and use it to cut out four pieces of craft foam, two pieces of PVC fabric, and two pieces of regular fabric. Pay attention to right vs. left soles as you do this.

Step 2:

Essentially you are making a sandwich of PVC on the bottom (with the PVC side outwards so that it will be the very bottom of the sole, the part that makes contact with the ground), two layers of foam, and then the fabric layer on top. Between each layer is a liberally applied coat of Shoe Goo.

I suppose other glues are possible, but I highly recommend Shoe Goo. It is designed specifically for shoes in that when it dries it is clear, solid and non-tacky, but still has some flexibility. Plus the hold is superior. Nothing is going to get your layers apart. It is not easy to work with however as it sticks to everything in its wet state. This is why I recommend using a popsicle stick to spread it. However I ultimately still ended up using my fingers at some points, so be sure to have a good hand cleaner present. Something like Fast Orange is ideal, but I got by with a dish scrubber and some dish soap.

Step 3:

Give the sole a full 48 hours to dry and cure. That was a lot of glue, after all. Then you can finally add the last layer – the slipper itself! Make sure you give it about 24 hours to dry and cure.

Ta-da!

…more of my crafted wedding

I forgot a few things! Too much DIY with this wedding, and all done within the past few months: it just all blurs together.

This was my hairpiece. I made it out of the lace from my mom’s wedding dress.

tumblr_mu1ujrirhr1roq7h8o1_500

And I made these ones for my bridesmaids.

Here they are in action:

Last, but not least, here is the ring bearer box and pillow. I did the sewing, my (now) husband made the box.

Make your own purse from duct tape

Just a quick post to share a free craft pattern I’ve developed.

At work we needed to have programs for the tweens and teens this summer that were of a creative, crafty, makey variety. So, I thought about duct tape, simply because it’s easy to make cool stuff with and it comes in some pretty neat colours and patterns now.

Then I thought “what can we make with it?” It had to be simple but useful. I decided on clutches and/or wallets (made the same way but a smaller size). I spent some time Googling, some time looking at books like this one.

But I wasn’t really finding what I wanted. This and this were the closest, but no real instructions were given.

So, I wrote Make your own clutch.

Here are some pictures of the fun the kids had, and how super creative they were!

 (cropped to remove faces for privacy. These are kids after all)
Copy of clutch craft 3

Copy of clutch craft 7

Copy of clutch craft 5

clutch craft 9

Copy of clutch craft 6

Flora and Fauna

First, the fauna:

Happy Easter Monday! From Desmond

Now for the flora:

As mentioned in previous posts, I (with the help of some awesome fellow knitters) am knitting the flowers for my wedding in addition to my shrug. This is why I’ve essentially been away from the blogosphere for the past month or so. That and the other elements of wedding planning and getting ready to move in May. Now I finally have some actual FO flowers worth sharing, so I thought I would.

First is this tulip from Lesley Stanfield’s beautiful book 100 Flowers to Knit & Crochet. (she has also made it available in a few other places, one for free!). I think it might be my favourite so far.

So favourited, I had to take several pictures.

Here are the others I’ve been working on:

An anemone, also from Lesley’s book.

This calla lily is another favourite. The pattern is by Cathy Ren.

A peony, also from Leslie’s book.

And lastly, a rose. It’s this pattern I mentioned in this post.

I think the calla lily and tulips will win out as the bouquet flowers. Now to figure out what I want to do for corsages and boutonni√®res…

Last minute gifts to make

Here’s a copy of a blog post I did for work. Enjoy!

Link to the original: Last minute gifts to make.

Ok, so it’s not really last minute if you’re shopping, but if you plan on making gifts to give this holiday season, the time to start is now!

Here are some great books full of instructions and inspiration.

(click on a title for link to item)

For those who celebrate Christmas:

Index

Index4

Index2

Or any of these other titles.

Or perhaps you celebrate Hanukkah?

Index

See more here.

How about Kwanzaa?

Index

See more here.

And then there are resources everyone can use:

Index

more card making resources here.

Maybe you have a particular craft you’re drawn to?

If you’re a knitter like me you might want to try searching for books with patterns for knitted gifts, such as this one:

Index

Or, if you aren’t the fastest knitter (also like me) or are running out of time (me again), try some of the quick-n’-easy patterns in these books:

Index

Index

Into paper crafts? Want to make someone their very own unique fabric-bound journal? Try a search like this, to get books like this:

Index

Beading? Try a search like this one to get books like this:

Index

Wood working? How about searching for books like this:

Index

The possibilities are endless.

And don’t forget to have a gander at our librarian¬†Recommended Websites¬†too.

Happy Holiday Handcrafting!